Attack Shark L60 Headset Fit: Comfort Setup Guide

By Attack Shark | Premium Gaming Keyboards, Mice, Headsets ... | Published: 2026-10-13

Category: How-to Guides

Get a stable, low-pressure fit from the Attack Shark L60 ultra-light headset with a step-by-step comfort setup, from band sizing to dual-wireless mode checks.

Quick answer

Start by extending the headband one notch at a time until the earcups sit centered over your ears with no downward pressure on the crown. Then confirm the L60 is in the right wireless mode, because a loose or poorly seated fit plus the wrong connection is the usual cause of discomfort and audio complaints. If the headset still pinches after these steps, the L60's fixed headband is a real limitation rather than a setup problem.

Why the L60's low weight changes how you fit it

The ATTACK SHARK L60 Ultra-Light Tri-Mode Gaming Headset is built around low weight, so the clamping force you feel comes mostly from the headband arc and how far you extend it, not from heavy earcups dragging the frame down. That matters because a light headset can feel fine for ten minutes and then reveal a pressure point after an hour of ranked play.

The L60 also uses ATTACK SHARK SmartSwitch dual wireless, which lets you toggle between HyperSpeed Wireless 2.4GHz and Bluetooth modes. Mode choice does not change physical fit, but it changes how you move: 2.4GHz keeps latency low for competitive play, while Bluetooth is better for casual listening and calls. Pick the mode before you settle the fit so you are not re-adjusting mid-session.

Check your desk and posture before you blame the headset

Fit problems often start below the neck. If your monitor is too high, you tilt your head back and the headband slides; if it is too low, you tilt forward and the earcups press against your jaw. Set the top of your screen near eye level and keep your shoulders relaxed before you adjust the L60.

Also check cable and dongle routing. A 2.4GHz receiver plugged into a rear USB port behind a metal case can add interference, and a short or snagged cable can tug the headset sideways. Move the receiver to a front or top port, or use a short extension, then re-check the fit.

How to test whether the fit is actually correct

A correct fit passes three quick checks. First, the earcups should sit centered over your ear canals, not on your jaw or above your ears. Second, the headband should rest on the crown with even contact, not a single hot spot. Third, you should be able to shake your head gently without the headset shifting more than a few millimeters.

If any check fails, change one thing at a time. Adjusting the band, the earcup angle, and the mic position all at once makes it impossible to know which change helped. Give each adjustment a full ten minutes of play before deciding.

L60 comfort setup in six steps

1. Extend the headband one notch at a time: Put the L60 on and extend each side equally until the earcups sit centered over your ears. Keep both sides even so the headband stays level on your crown. Mistake to avoid: extending only one side, which tilts the frame and creates a single pressure point.
2. Rotate the earcups to match your head shape: Tilt each earcup slightly forward or back until the cushion seals around your ear without pressing on your jaw or the top of your ear. Checkpoint: if you feel pressure above your ear, the band is too short; if you feel it on your jaw, the earcup angle is wrong.
3. Set the mic so it does not pull the headset: Position the boom so it sits just off the corner of your mouth and does not drag the left earcup forward. Re-check the fit after moving it. Mistake to avoid: leaving the mic pressed against your cheek, which pushes the earcup off-center over time.
4. Choose 2.4GHz or Bluetooth before you play: Use HyperSpeed Wireless 2.4GHz for competitive, low-latency play and Bluetooth for casual listening or calls. Toggle with SmartSwitch rather than re-pairing. Checkpoint: confirm the correct mode is active so you are not troubleshooting latency when the real issue is fit or seating.
5. Take a 10-minute break-in test: Play or listen for ten minutes, then note exactly where you feel pressure. Adjust one variable, such as band length or earcup angle, and repeat. Mistake to avoid: changing several settings at once and losing track of what actually helped.
6. Re-check after 60 minutes and adjust posture: After an hour, re-check the three fit tests and your monitor height. If discomfort returns in the same spot every session, the L60's fixed headband may simply not match your head shape. Next step: if pressure persists after two or three sessions of careful adjustment, consider a headset with a different band design.

Product facts behind this guide

ATTACK SHARK L60 Ultra-Light Tri-Mode Gaming Headset: ATTACK SHARK SmartSwitch dual wireless headphones let you quickly toggle between HyperSpeed Wireless 2.4GHz and Bluetooth modes, with lossless audio, high-speed transmission, and extremely low latency. You can keep one headset for low-latency competitive play and casual Bluetooth listening, but you should confirm the active mode before judging audio quality or fit during a session.